< Previous 1-800-450-8665 A & B Measurement Gauge Our new A & B Measurement Gauge is now available to accurately provide you with the A & B measurements needed for your edging department. Order Number: GAGE-17-31 NEW! A & B Measurement Gauge 1-800-450-8665 BUILD A SHAPE GAUGE When defects are discovered on the edge of a lens, the “Build A Shape” eliminated the guess work out of determining if a defect can be cut out. “Build A Shape” will save your lab service time and the cost of redoing a perfectly good lens. Sample Work Ticket Example 55mm Eye Size 5mm Decent ration 35mm “B” Measurement Seg Ht 16mm high Picture shown with 55 Eye Zero Dec /Bifocal on Center STEP 1: Slide lower corner pieces to the eye size you need to create. At this point the OC or Bifocal is on center. Continued on Next Page BUILD A SHAPE Work Ticket Sph Cyl Axis R: +.25 -.50 x130 L: -1.25 -.75 x95 Dpd Npd Seg Ht R: 63 60 16 L: 63 60 16 (Dec) R L Layout HOR: +5.0 +5.0 Layout VER: -1.5 -1.5 Thickness [MRP] 2.56 2.37 Min Edge 1.9 2.1 Max Edge 2.4 2.3 Circumference 152.7 152.7 Frame Metal [55.0] 55.00 : 15.00 B: 35.00 ED: 58.00 1-800-450-8665 Picture shown as Right Eye Size 55mm with decent ration 5 In STEP 2: For a Right Eye, slide the lower corner pieces to the left by the amount of decent ration listed on the work ticket. Bifocal is now positioned to the right of center. For a Left eye, slide corner pieces to the right. Picture shown as Right Eye Size 55mm with decent ration 5 in Vertical measurement of 35mm. STEP 3: Align upper corners to lower corners, position vertical at 35mm. Shape is ready to see if lens or defect in lens will cut out. Order#: GAGE-15-29 1-800-450-8665 Drilled Rimless Hole Gauge 1.00mm – 1.25mm Indexing Gage ORDER NUMBER: PTT1784-1 Take the guess work and spoilage out of sizing drilled, rimless lenses with Precision Tool Technologies Indexing Drilled Rimless Hole Gauges. Each gauge has six index pins (replaceable if worn or damaged) and the five piece set spans hole sizes from 1.00mm to 2.45mm in .05mm increments. Very accurate and easy to use. Five Piece Set ORDER NUMBER: PTT1784 1.30mm – 1.55mm Indexing Gage ORDER NUMBER: PTT1784-2 1.60mm – 1.85mm Indexing Gage ORDER NUMBER: PTT1784-3 1.90mm – 2.15mm Indexing Gage ORDER NUMBER: PTT1784-4 2.20mm – 2.45mm Indexing Gage ORDER NUMBER: PTT1784-5 1-800-450-8665 Precision Lens Alignment Gauge Precision Tool Technologies offers this one-two punch for your edging operation. The Lens Alignment Gage allows a quick and accurate check for axis and bifocal alignment by comparing both lenses simultaneously. Costly blocking errors are detected and rework prevented. Sizes: 65mm & 90mm Order Number Table Gage- 7- 65mm Lens Capacity 20A Weco 9- 90mm Lens Capacity 20B Essilor 20C AIT 20D Semi Tech 20F Gerber Step 2 20G Santinelli/Nidek 20H AIT Indo 20I Santinelli 7000 Twisted Lens Alignment Gauge Fixture Model Shown: Gage-8-20A The Twisted Lens Alignment Fixture quickly and accurately determines if your lens slipped off axis during the edging process. This fixture is simple to use yet, very accurate. The Twisted Lens Alignment Fixture is extremely beneficial in checking drilled mount lenses. Order Number Insert Style Gage-8-20A Weco Gage-8-20B Essilor Gage-8-20C AIT Gage-8-20D Semi Tech Gage-8-20F Gerber Step 2 Gage-8-20G Santinelli/Nidek Gage-8-20H AIT Indo GAGE-8-20I Santinelli 7000 Alignment and Twisted Gauge Inserts All Finishing gauges shown can be adapted to your block type. Precision Tool, LOH and Weco Style Edging Blocks Essilor Style Edging Blocks AIT Style Edging Blocks Semi Tech Edging Blocks Gerber Step 2 Style Edging Blocks Santinelli / Nidek Edging Blocks AIT Indo Style Edging Blocks Santinelli 7000 1-800-450-8665 Back to Back Acrylic Axis Gauge Shown with Weco Inserts The back to back gauge allows a quick, accurate visual inspection of blocked or edged lens pairs. Any error in blocking or slippage during edging will be picked up by the parallel etched lines on the acrylic base. Lines are etched on both surfaces to prevent errors in parallax. Inserts available in most edge block designs. Order Number: Configuration: GAGE-12A-20A WECO Side by Side Acrylic Axis Gauge This new Side By Side gauge allows a quick, accurate visual inspection of blocked or edged lens pairs like the back to back above but now you can have it in a side by side. Any error in blocking or slippage during edging will be picked up by the parallel etched lines on the acrylic base. Lines are etched on both surfaces to prevent errors in parallax. SHOWN WITH OUR QC2 LENSES Order # GAGE-14A-20A 1-800-450-8665 Is your lab having problems laying out the 180° line on demo lenses? We have the solution for you! We have a base weighted, precision ground, easily adjustable marking pen designed for easy use. To assure the proper frame orientation or pantiscopic tilt, we have an easy to use pantiscopic tilt table and pen tip reference gage to make sure the lens curve is properly aligned! Order Today! Order# Description PTT2350-KIT “Perfect Mark” 180° marker system Comes complete with table, tip gauge, pen holder and 2 markers Included with the “Perfect Mark” 180 ° system 1-800-450-8665 Order Number: PTT2574-PTT NEW! Pantoscopic Tilt Tool Now available from Precision Tool Technologies the Pantoscopic and Vertex tool. Quick and easy to use to determine Pantoscopic tilt with a pre-adjusted frame. On the back of this tool you be able to use it to measure the Vertex distance. Platen fits the Bausch and Lomb model 70 lensometer Platen for B&L Lensometer Increase the versatility of your lensometer with this enlarged platen. You can now accurately measure lens power in the ever more popular wrap-around style frames. Order Number: PTT2014 Finishing Gauges 1-800-450-8665 NEW IMPROVED PLATEN FOR MARCO 101 USERS Order Number: PTT2014-101-ASY To be used on Marco 101 Lensometers (shown with riser plate sold separately) Many labs have benefited from the Frame Riser plate to elevate small frames into the viewing field of the scope. New wrap frames pose another problem. Their shape doesn’t allow the existing platform to support the frame. The operator is forced to balance the frame which results in compromised readings. Precision Tool Technologies’ new riser plate has an extended leaf on both ends of the platform to support wraps. The exclusive sight window on the right side of the plate, keeps the gage wheel visible. Frame Riser Plate Frame Riser Plate Here is the solution to finding the optical center on today’s smaller frames. The Frame Riser Plate lifts the frame to the geometric center. This eliminates the false reading of vertical prism caused by checking above the optical center. The plate easily attaches to Marco and B&L Lensometers to extend the lift needed for today’s smaller frames. Offered in 2 styles - Small plate with Marco clip. Slightly larger plate with the B & L clip. Order Number: Lensometer Size/mm PTT1868-ASSY Marco 24 X 148 PTT1868-BL-ASSY Bausch &Lomb 28 X 158 1-800-450-8665 Next >